strange error pop up - file not found for script

Wally Mayo · Post by **Wally Mayo** » Fri May 05, 2006 1:24 pm

Error message pops up saying "Digital Atmosphere encountered an error: file not found" after doing following script one line at a time. Actually, fronts ingest and they plot just fine, but curiously, the error box then pops up.

download,http://www.hamweather.net/weather/asus0 ... fronts.dat
ingest,d:\digatm\data\fronts.dat
product,wxp,0,fronts

Using version 0.6c I guess ... the patch install file says "c" but during the patch, the install box says "b", and the software says "b" at the top when running.

Fred · Post by **Fred** » Thu May 18, 2006 4:37 pm

I had the same error message with fleet. As far as I remember it disappeared when I downloaded and plotted the fleet interactive. After that the script performed fine....?????

britbob · Post by **britbob** » Sun Jul 23, 2006 11:11 pm

This is one that has been puzzling me for a while. So I stumbled across what might be the cause.

Today I installed Fusion on my other PC, which runs Windows 2000 pro. Fusion runs alone on this, DAWS is not installed on it.

Well, just by chance I ran the same script I was having problems with on the other machine, low and behold the script runs flawlessly.

I can only assume this is either an issue with windows 98 which is on my main DAWS machine, or because the original DAWS is installed on the same hard drive.

I`m formatting my other machine removing windows 98, and installing windows 2000 as the OS. I`ll just install Fusion and nothing else and see how it goes.

britbob · Post by **britbob** » Mon Jul 24, 2006 2:15 am

Well I`m absolutely puzzled by this one.

Both PC`s now have the exact same operating system. I`m running Fusion on my smaller PC which I was using to run scripts in DAWS 24/7.

In bouyant mood expecting to see my scripts running again, well that was a dissapointment

On my smaller PC I`m back to the `file not found` popup error as soon as the fronts have plotted.

I don`t get it because the same script runs perfect on my main pc. All the paths/directories are exactly the same for both machines. So why the heck will they not run on my other machine, which apart from the hardware is exactly the same.

FWIW, here`s a sample of the script

load,C:\Documents and Settings\Bob\My Documents\DAWS\basemaps\canada800.dmf
download,http://www.hpc.ncep.noaa.gov/discussion ... \Documents and Settings\Bob\My Documents\DAWS\data\fronts.dat
download,http://www.atmos.albany.edu/weather/dat ... \Documents and Settings\Bob\My Documents\DAWS\data\synop.dat
download,http://www.atmos.albany.edu/weather/dat ... \Documents and Settings\Bob\My Documents\DAWS\data\synbouy.dat
ingest,C:\Documents and Settings\Bob\My Documents\DAWS\data\*.dat
product,wxp,0,fronts
ANALYZE,HILO CONT CINT=4 COLOR=64:64:64 LINE=1 SLPR
import,C:\Documents and Settings\Bob\My Documents\DAWS\basemaps\surfaceanaloverlay800.gif
stamp
export,C:\Documents and Settings\Bob\My Documents\DAWS\products\canada_surface.png

Again, the above works fine on one machine but crashes on the other. It always fails after the fronts have plotted.

I would have thought a machine would run Fusion which ran DAWS fine.

Mmmm, not sure what else to try

This was reported several months ago a few folks, hopefully Tim can fix this up.

Weasel · Post by **Weasel** » Mon Jul 24, 2006 2:31 am

Wally,

Running DA WS 1.1j3 and Fusion v0.6e2 at the same time, on the same hard drive does not cause this error (perhaps it was corrected in a Fusion patch after v0.6c?).

I just copied your script and everything worked perfectly as the data from HPC, via Hamweather, plotted the fronts, running both DA WS and Fusion from the same hard drive.

Maybe if you could post your entire script, Wally? I don't know if there is more to it or not, but maybe something else will show the error when I copy and run it on my computer.

Pat

britbob · Post by **britbob** » Mon Jul 24, 2006 2:44 am

I`m not Wally but as I`ve tried every else, this must be hardware related? Why else would the script fail on one machine, but run on another. Both machines running identical operating systems etc.

The failing machine is fairly old. 300mhz Pentium, 196mb ram but it should work as it handled DAWS for many months. For some reason my old machine has an issue after frontal depictions have been plotted in a script. If I remove the front command(s) from the script, all the maps then carry on to plot the isobars perfectly.

Weasel · Post by **Weasel** » Mon Jul 24, 2006 2:54 am

Bob,

I just ran this script from your earlier post (minus stuff that is irrelevent to my machine):

download,http://www.hpc.ncep.noaa.gov/discussion ... fronts.dat
download,http://www.atmos.albany.edu/weather/dat ... \synop.dat
download,http://www.atmos.albany.edu/weather/dat ... ynbouy.dat
ingest,C:\digatm\data\*.dat
product,wxp,0,fronts
ANALYZE,HILO CONT CINT=4 COLOR=64:64:64 LINE=1 SLPR

Fronts and isobars plotted without any error running the latest DA WS and Fusion from the same hard drive.

Maybe it is some odd sort of problem with older computers?

Pat

Edit: I added this last line to the script to exclude any imagery export problems (I use the \us directory for all exported charts):

export,C:\us\canada_surface.png

No errors were encountered after adding this line.

britbob · Post by **britbob** » Mon Jul 24, 2006 3:08 am

Odd indeed!!

As there`s not a lot else I can think of at the moment. I might try a different graphics card in the machine, also maybe stick another ram stick in there. Doesn`t hurt to try

I`m off the bed...............

Ps. I wonder if this could be direct x related?

Weasel · Post by **Weasel** » Mon Jul 24, 2006 3:14 am

Yes it is getting rather late in your neck of the continent :)

Hard to say just where the problem may be. Try your theories and let us all know if they fix the trouble!

Pat

britbob · Post by **britbob** » Mon Jul 24, 2006 1:24 pm

Success - I hope!!

Just installed DirectX9 onto the troublesome machine and the script has just run all the way through.

I`ll keep testing it today and see how things go